Marc, it's soooo big! I don't think Dave can measure up.
*ahem*
And it kicks ass. .
New Space Wrecker
Moderator: VLC Directors
- Dj_Max
- Master Poster
- Posts: 811
- Joined: Fri Nov 07, 2003 8:29 pm
- Location: New Westminster (Queensboro)
- Contact:
Xandria wrote:Marc, it's soooo big! I don't think Dave can measure up.
*ahem*
And it kicks ass. .
Hehehehe, I wouldn't want Dave to feel inferior (weelllll maybe!)
I don't know if you noticed, but the front of the ship is angled.
I took the wings from the X-Wing fighter and put them side by side on the angle side and attached them with hinge plates.
It was the start of a brand new Space Wrecker.
Now I simply have to complete the interior... ugh!
Cheers!
Marc B
VLC President 2005-06
VLC Archivist 2004-05
Marc B
VLC President 2005-06
VLC Archivist 2004-05
Very nice ship! My only real complaint is that it just has this sort of 'look' to it because of all the flat plates with studs used on it. I feel like there's some aspect of it I don't especially like, and yet I can't figure out what to change for it. Very nice angle work at the front too, although I think it could be sculpted to flow a bit better.
Just how large is this interior going to be? Does it extend into the front angled sections?
Great work with a large ship. Can't wait to see the inside.
Just how large is this interior going to be? Does it extend into the front angled sections?
Great work with a large ship. Can't wait to see the inside.
- Dj_Max
- Master Poster
- Posts: 811
- Joined: Fri Nov 07, 2003 8:29 pm
- Location: New Westminster (Queensboro)
- Contact:
It is going to be elevated a bit more.
I have a few ideas in my head as far as maybe retractable landing gears, shuttle bays, and of course the grappling hook.
The interior will be mostly througout the back end of the vessel, as the front is not high enough for fig clearance.
I have a few ideas in my head as far as maybe retractable landing gears, shuttle bays, and of course the grappling hook.
The interior will be mostly througout the back end of the vessel, as the front is not high enough for fig clearance.
Cheers!
Marc B
VLC President 2005-06
VLC Archivist 2004-05
Marc B
VLC President 2005-06
VLC Archivist 2004-05
- Dj_Max
- Master Poster
- Posts: 811
- Joined: Fri Nov 07, 2003 8:29 pm
- Location: New Westminster (Queensboro)
- Contact:
Look at my post above yours... sigh...Brickhead wrote:not to be critial , but i think J1A3L5 is right . there something that just doesn't look right , Maybe the fact that its sitting flat on a table , like with no landing gear or anything. Is the whole bottom flat ?
just my opinion
Cheers!
Marc B
VLC President 2005-06
VLC Archivist 2004-05
Marc B
VLC President 2005-06
VLC Archivist 2004-05
- Dj_Max
- Master Poster
- Posts: 811
- Joined: Fri Nov 07, 2003 8:29 pm
- Location: New Westminster (Queensboro)
- Contact:
Construction has halted. The contractor tried to elevate the entire contraption, but got a little too miffed, and was just about to scrap the whole thing.Dj_Max wrote:It is going to be elevated a bit more.
I have a few ideas in my head as far as maybe retractable landing gears, shuttle bays, and of course the grappling hook.
The interior will be mostly througout the back end of the vessel, as the front is not high enough for fig clearance.
So he decided to put a pause on any further building of any sorts until further notice.
Cheers!
Marc B
VLC President 2005-06
VLC Archivist 2004-05
Marc B
VLC President 2005-06
VLC Archivist 2004-05